What is peptide reconstitution?
A 5 mg vial of peptide, 2 mL of bacteriostatic water, and a 250 mcg dose means you draw 10 units on a U-100 insulin syringe. That sentence is the whole job of this page. The Peptide Dosage Calculator takes the three numbers you already have and tells you where to stop the plunger.
Peptides for injection usually ship as a dry powder, called lyophilized, sealed in a small glass vial. The label tells you how much peptide is inside, in milligrams. Before you can use it, you add a measured amount of sterile liquid, usually bacteriostatic water. That step is reconstitution. Once the powder dissolves, every millilitre of liquid holds the same share of the peptide.
The catch is that insulin syringes aren't marked in milligrams. They're marked in units, and a unit is a volume, not an amount of drug. So there's a conversion between the dose on your paper and the line on the barrel. It's three steps of arithmetic. It's also the kind of arithmetic where a slipped decimal gives you ten times the dose, and nobody should do it tired at the kitchen counter.
Plenty of calculators for this live on shop pages. You get the answer with a grid of vials under it and a pop-up asking for your email in exchange for a "dosing guide." Others are tracking apps that want an account, a trial, and then a monthly plan before they'll do one division. This page does the math, shows its work, and lets you leave.
How to use the peptide dosage calculator
There's no Calculate button. The result updates as you type.
- Type the amount of peptide in the vial, in mg. It's printed on the vial label, for example 5.
- Type how much bacteriostatic water you added, in mL, for example 2. Decimal commas work, so 2,5 is read as 2.5.
- Type your dose and pick mcg or mg next to it. The switch starts on mcg, because that's how most doses are written.
- Pick your syringe: 30, 50, or 100 units (0.3, 0.5, or 1 mL). Check the packaging if you're not sure.
- Read the big number: "Draw 10 units." Below it you get the draw volume in mL, the concentration of your vial, and how many doses the vial holds.
- Look at the syringe picture. The barrel fills to the line you need, so you can match it against the real one in your hand.
If a warning appears, read it before you draw. The calculator speaks up when the dose won't fit in the syringe, when the dose is bigger than the whole vial, and when the draw is too small to measure well. Nothing you type is saved or sent anywhere. The math runs in your browser.
This does the math, not the medicine. The Peptide Dosage Calculator never suggests a dose, and there are no peptide presets on the page. Your dose, and how and when to inject it, should come from your doctor.
How units to draw are calculated
Three short formulas, run in order. Each one feeds the next.
Concentration (mg/mL) = vial amount (mg) ÷ water added (mL)
Draw volume (mL) = dose (mg) ÷ concentration (mg/mL)
Units = draw volume (mL) × 100
The first formula tells you how strong the mixed vial is. The second tells you how much of that liquid carries your dose. The third turns millilitres into syringe units. On a U-100 syringe, 100 units fill exactly 1 mL, so each unit is 0.01 mL.
A worked example
Say the vial holds 5 mg, you added 2 mL of water, and your dose is 250 mcg.
- Concentration: 5 mg ÷ 2 mL = 2.5 mg/mL, which is 2,500 mcg in every mL.
- Draw volume: 250 mcg is 0.25 mg. 0.25 mg ÷ 2.5 mg/mL = 0.1 mL.
- Units: 0.1 mL × 100 = 10 units.
- Doses per vial: 5 mg ÷ 0.25 mg = 20 doses.
The calculator prints that exact line under the result, with your numbers plugged in: 5 mg ÷ 2 mL = 2.5 mg/mL · 0.25 mg ÷ 2.5 mg/mL = 0.1 mL · 0.1 mL × 100 = 10 units. You can copy it, paste it into a note, and check it by hand.
Why you see 14, not 13.999999999999998
Computers store decimals in binary, and binary can't hold most decimals exactly. Work out a 350 mcg dose from a 5 mg vial with 2 mL of water the obvious way, 0.35 ÷ 2.5 × 100, and plain JavaScript gives you 13.999999999999998. The peptide dosage calculator avoids that by doing the math in micrograms and multiplying before it divides, so the answer is a clean 14. Units are then rounded to one decimal, which is already finer than any syringe marking.
Common concentrations and syringe markings
The table below shows what one unit holds for the vial sizes and water amounts people type most often. The last column uses 100 mcg as a round number to scale from. It's a reference for the arithmetic, not a dose.
| Vial | Water added | Concentration | Peptide in 1 unit | Units per 100 mcg |
|---|---|---|---|---|
| 2 mg | 1 mL | 2 mg/mL | 20 mcg | 5 |
| 2 mg | 2 mL | 1 mg/mL | 10 mcg | 10 |
| 2 mg | 3 mL | 0.667 mg/mL | 6.67 mcg | 15 |
| 5 mg | 1 mL | 5 mg/mL | 50 mcg | 2 |
| 5 mg | 2 mL | 2.5 mg/mL | 25 mcg | 4 |
| 5 mg | 3 mL | 1.667 mg/mL | 16.67 mcg | 6 |
| 10 mg | 1 mL | 10 mg/mL | 100 mcg | 1 |
| 10 mg | 2 mL | 5 mg/mL | 50 mcg | 2 |
| 10 mg | 3 mL | 3.333 mg/mL | 33.33 mcg | 3 |
Two things jump out. First, the water doesn't change how much peptide is in the vial. It only changes how many units carry it. A 5 mg vial with 1 mL of water puts 250 mcg in 5 units. With 2 mL it's 10 units, with 3 mL it's 15, and with 5 mL it's 25. Same dose every time, different line on the barrel.
Second, strong mixes make small draws. A 10 mg vial in 1 mL puts 100 mcg in a single unit. One unit is hard to see, let alone hit. That's why the calculator nudges you toward more water whenever a draw drops under 2 units. Bigger numbers are easier to read.
What each syringe holds
| Syringe size | Capacity | Volume per unit | Typical markings |
|---|---|---|---|
| 0.3 mL | 30 units | 0.01 mL | Every unit, some every half unit |
| 0.5 mL | 50 units | 0.01 mL | Every unit |
| 1 mL | 100 units | 0.01 mL | Every 2 units |
Every U-100 syringe uses the same unit, whatever its size. What changes is how finely the barrel is marked. A 7.5-unit draw sits between two lines on a 1 mL syringe, but lands on a half-unit mark on some 0.3 mL syringes. If your draws are small, the smaller syringe is easier to read.
Mistakes the calculator catches
The math is simple. The ways it goes wrong are also simple, and each one gets a plain-language warning. Here's what they look like.
Mixing up mcg and mg
1 mg is 1,000 mcg. Doses are often written in mcg while vials are labelled in mg. Type 250 with the switch on mg by accident and you're asking for 250 mg from a 5 mg vial. The calculator hides the units and says: "That dose is more than the whole vial. Check mcg vs mg. That's the usual mix-up." It won't show a number for a dose the vial can't hold, because any number there would be wrong.
A dose that won't fit in the syringe
A 1 mg dose from a 5 mg vial mixed with 3 mL of water is 60 units. A 50-unit syringe stops at 50. The calculator still shows 60, adds "That's 60 units, and this syringe holds 50. Pick a bigger syringe or split the dose," and draws the barrel full with an "Over by 10 units" marker. It never clips the answer to the top of the barrel. A clipped number looks exactly like a correct one. Switch to the 100-unit syringe and the warning clears.
A draw too small to measure
A 10 mg vial with 1 mL of water and a 50 mcg dose works out to 0.5 units. That's half of the smallest mark on most syringes. The calculator shows the result and suggests more water. The same dose from the same vial mixed with 5 mL is 2.5 units, which you can actually see.
Commas and decimals
People in Germany, Poland, and Russia write 2,5 for two and a half, and the calculator reads it that way. But 2,500 is a real problem: it could mean 2.5 or 2,500, a 1,000× difference. So the calculator asks instead of guessing: "Did you mean 2.500 or 2500? Type it without the comma."
Using a U-40 syringe
Every unit on this page is a U-100 unit. U-40 syringes, mostly sold for pet insulin, fit 40 units in 1 mL, so each mark holds 2.5 times as much liquid. If that's what you have, use the draw volume in mL and multiply by 40. A 0.1 mL draw is 10 units on U-100 and 4 units on U-40. Right math, wrong syringe, wrong amount.
If the result looks off, check in this order: the mcg/mg switch, the vial label, the water you actually added, then the syringe type. The switch is the usual culprit. If you're still not sure, ask the pharmacist or doctor who gave you the dose. That's a normal question, and they'd rather you ask.
Related calculations
Doses and vials don't always use the same unit. The unit converter turns mcg into mg and back, and the weight converter covers grams and larger units if a label uses them.
The mg to mL converter handles a different problem: turning a mass into a volume using a liquid's density. For a reconstituted vial, density doesn't matter. The concentration you created decides the volume, which is why the peptide dosage calculator asks how much water you added.
If you work in a lab, reconstitution is the same idea as making up a stock solution. The molarity calculator does that math in moles per litre instead of mg per mL.
Frequently asked questions
How many units is 250 mcg?
It depends on how strong the vial is, which depends on the vial size and the water you added. From a 5 mg vial with 2 mL of water, 250 mcg is 10 units. With 1 mL it's 5 units, and with 3 mL it's 15. A unit measures volume, not peptide, so there's no single answer without your vial's numbers.
How much bacteriostatic water should I add?
The calculator doesn't pick that for you. Follow the instructions from whoever prescribed or supplied the vial. What the math can show you is the tradeoff: more water gives a weaker solution and bigger, easier-to-read draws. Less water gives smaller draws. Try a few amounts in the calculator to see how the units change before you mix.
Does adding more water change my dose?
No. A 5 mg vial holds 5 mg whether you add 1 mL or 3 mL. Water only spreads the peptide out, so you draw more units for the same dose.
What does U-100 mean on an insulin syringe?
It means the syringe is marked for 100 units per mL, so each unit is 0.01 mL. Almost every insulin syringe sold for people is U-100. The markings are a volume scale. They don't know what's inside the syringe.
What does "doses per vial" count?
The whole vial divided by one dose, rounded down. A 5 mg vial at 250 mcg is 20 doses. Treat it as a ceiling, since a little liquid stays behind in the vial and the syringe each time.
Why does the calculator say my dose is more than the vial?
Because the dose you typed, in the unit you picked, is bigger than the vial's total amount. It's almost always the mcg/mg switch. Flip it and the result appears.
Can I use this peptide dosage calculator on my phone?
Yes. It fits small phone screens, every field opens the number keypad, and there's no account or app to install. Open it, type three numbers, read the units.