- How many taps do I need?
- Two gives you a number, but it's a guess — one interval, and whatever jitter is in your hand goes straight into the answer. Four is usually within a beat or two of correct. Eight is solid. The reading averages every tap in the run rather than the last few, so it converges rather than wobbling: each extra tap has less influence than the one before it, and the line under the pad switches to 'steady' once the intervals agree to within about five percent.
- It says 64 and the track is clearly faster than that. What happened?
- You tapped every other beat. It's easy to do on anything with a slow-feeling groove — half-time hip-hop, drum and bass, a lot of dubstep — because the snare you're hearing lands on the half-time pulse rather than the beat. Hit ×2. The correction is persistent, so you can keep tapping afterwards and the reading stays doubled. ÷2 does the opposite when you've accidentally tapped twice per beat, which happens on fast tracks where the hi-hat is more audible than the kick.
- Why doesn't this play a click?
- Because your music is already playing, and a second sound would fight it. Measuring a tempo and playing a tempo are opposite jobs: here you know the song and want a number, and a click at you is noise. If you want the click — to practise to, to record to, to count a band in — that's the metronome, which does have sound and has this same tap feature built into it for nudging the tempo while it runs.
- How accurate is tapping compared to software that detects BPM automatically?
- For a track with a steady grid, a well-tapped run lands within a fraction of a BPM of what a DAW's analysis gives you — the arithmetic is exact, so the only error is in your hand, and averaging a long run cancels most of it. Automatic detection wins on two things: live-recorded music that drifts, where there is no single right answer, and octave errors, which it also gets wrong regularly. It loses on everything else, because it needs the audio file. You can tap along to a record, a radio, a rehearsal room, or a video playing on someone else's phone.
- What do I do with the number once I have it?
- Type it into your project tempo before you record anything — getting it right first means your grid, your delays, and any loops you drop in all line up without warping later. DJs use it to spot a pair of tracks that will beatmatch without a big pitch change; anything within about six percent rides on most mixers. Fitness instructors build playlists around a target range — roughly 130 to 150 for a running class, 120 to 130 for strength work. Copy gives you the whole number because that's what every tempo field expects.
- Why does it stop at 20 and 300?
- Below 20 BPM the beats are more than three seconds apart, which is also the point where a pause is indistinguishable from you stopping — so the run resets instead of reporting a tempo. Above 300 you're past the top of any tempo marking and almost certainly double- or quadruple-tapping, so the reading clamps rather than showing a five-figure number from a stray fast pair. Most recorded music sits between 60 and 180, so neither limit gets near a real song.
- What counts as a pause?
- Three seconds without a tap ends the run. The next tap starts a fresh one at count 1 and the readout goes back to a dash. That's deliberately longer than a metronome's tap reset: at 40 BPM the beats are already a second and a half apart, and human tapping wanders, so a shorter threshold would cut slow tapping off mid-run. It also means switching tracks needs nothing more than stopping for a moment — no Reset click required, though Reset is there if you want to clear the multiplier too.
- Does the Space bar work if I'm holding it down?
- Holding it registers one tap, not a stream of them. Key repeat is ignored — you have to release and press again for the next beat. That matters more than it sounds, because a key that repeated would give you a tempo of several hundred within a second of leaning on it. On a phone, one touch is one tap for the same reason.
- Do I need an account, and does anything get uploaded?
- No to both. The tapping happens in your browser, the arithmetic runs on your device, and nothing about the song or your taps is sent anywhere or saved. There's nothing to sign into, no limit on how many tracks you measure, and no consent dialog in front of the pad. Close the tab and it's gone.
- How does this compare with looking the track up in a BPM database?
- A database is useful when you know the exact release and it happens to be listed. It's slower when you don't: you type a title, pick between six versions, and the number you get belongs to whichever master someone indexed — not necessarily the edit, remix, or pitched-up copy you're actually playing. Tapping takes about four seconds and measures the audio in front of you, which is the one that matters. It also works on unreleased material, a rehearsal, or anything you can hear but can't name.